Threadlocking Adhesives DL0290

DL0290　

Moderate intensity, low viscosity, the high permeability, fast curing, suitable for the inert surface. For locking and sealing M2~M12 thread already assembling. Can be used for sealing welds, casting sand holes etc (under 0.10φ) porous micropore, may spread glue on the screws by brush . Strengthen the pressure assembly intensity and seal it etc.

Retaining Compounds

LITAI Retaining compounds are applied to increase the shear strength of cylindrical, non-threaded assembles. Excellent gap filling ability, flexibility, high strength and prevent corrosion characteristics, hightite retaining compounds can replace of transition and interferences fits and reduce stress and deformation assembly.

Product No	Color	Max Gap Filling mm	Properties			Cure Time
			Viscosity	Shear Strength	Temp Range	Fixture Time	Full Cure Time
			mPa. s	N/mm2	0c	min	h
DL0603	green	0.13	100/160	≥ 22.	-55~150	20	24
DL0603	green	0.13	100/150	≥ 19	-55~150	10	24
DL0620	green	0.38	6000/12000	≥ 19	-55~204	30	24
DL0638	green	0.38	2200/3000	≥ 22	-55~150	5	24
DL0648	green	0.13	500/600	≥ 26	-55~175	10	24
DL660	silver	0.5	160000/360000	≥ 17	-55~150	10	24
DL0680	green	0.25	800/1800	≥ 21	-55~150	10	24

Threadlocking Adhesives DL0262

DL0262

High strength, suitable for most metal surface, thixotropy viscosity, well chemical resistance.

Can be used for locking and sealing under M20 thread.

Typical application: lock and seal the screws of engine ， can bear strong vibration etc.

Threadlocking Adhesives DL0290

DL0290　

Moderate intensity, low viscosity, the high permeability, fast curing, suitable for the inert surface. For locking and sealing M2~M12 thread already assembling. Can be used for sealing welds, casting sand holes etc (under 0.10φ) porous micropore, may spread glue on the screws by brush . Strengthen the pressure assembly intensity and seal it etc. http://www.litai-gz.com/pid11205674/Threadlocking+adhesives++DL0290.htm

Threadlocking Adhesives DL0242

http://www.litai-gz.com/pid11205648/Threadlocking+adhesives+DL0242.htm

middle intensity, universal, thixotropy viscosity, easy to disassemble. be suitable for locking and sealing M6 ~ M36 thread and strengthen key pin . Typical application: lock and fix screw, nut etc.

 

LITAI150

The liquid sealing belt to take the application
·Various specification tube thread seals completely the lock tightly, resolve because use the traditional material efficiency thoroughly low, seep into the serious problem, the quality is outstanding, useding for the chemical engineering extensively, the soldier work, fire fight, cold hot water, coal gas of air condition, supply water etc. profession
Cost advantage
·Usage originally article because of exaltation labor the artificial that efficiency save is is consumedly high in this article material fee.
Seal completely the mechanism
·This article is in the metals thread in the absence of the oxygen is namely solid to change in to bear aging, bear the corrosion, not poisonous not the flexible plastics of hot and solid that dissolve, bear the aging far longer than metals tube material.
Operate the important point
·Before install wiped the greasy dirt with the cotton.
·The above tube of DN65 is two-sided to draw the foot gum and put on even, twist as soon as possible while install tightly not grind to a stop and tune up the angle, the follow-up install to avoid the front have already install good just at solid turn of deal with contact to follow behind to turn to move.
· Used for the steel, copper, the iron piping material, the environment temperature 250 Cs is above,24 hours of －s try to press the 250 C ～ 150 Cs after install,48 hours of －s.The 150 C ～ 00 Cs,8-16 hours.Used for the stainless steel, aluminum, the metal alloy steel is solid to turn time to prolong 100%.
·Drink the pipe line to draw the gum in the outside tooth only
·The big specification tube dismantles to unload the strength big, can dismantle to unload with the coal gas air gun heating.
Regulation
·Use to draw the gum to brush not directly stretch into the bottle takes the gum liquid, proper draw the gum to brush to put on the gum liquid is crowded in taking care of the tooth, then use evenly.
·The gum liquid that extrude in the tooth from the tube because of contact oxygen long-last not solid turn.
·Pure oxygen, chlorine gas and strong oxidize sex to lie the quality of obsolescent.
·Must use the above work condition of 150 Cs please contact the my plant technique department